System Debugging

Serial Port Debugging

If you are involved in U-Boot or kernel development, a USB serial adapter (short for USB to serial TTL adapter) is very useful for checking system boot logs, especially when there is no graphical desktop display.

Choosing an Adapter

There are many USB to serial adapters available online. By chip type, the following serial ports are recommended:

Serial Port Maximum Baud Rate Recommended Review Purchase Link
CP2102 2Mbps Recommended Supports high baud rate communication, good stability and durability

Note: The default baud rate for LPA3399Pro is 1500000. Some USB to serial chips may not reach a baud rate of 1500000, and there may be differences between different series of the same chip, so make sure to confirm support before purchasing.

Hardware Connection

The USB to serial adapter has four pins:

  • 3.3V power (NC), no connection needed

  • GND, the ground wire of the serial port, connected to the GND pin of the development board’s serial port

  • TXD, the output wire of the serial port, connected to the TX pin of the development board’s serial port

  • RXD, the input wire of the serial port, connected to the RX pin of the development board’s serial port

  • Note: If you encounter problems with TX and RX input and output using other serial adapters, try swapping the TX and RX connections.

LPA3399Pro serial port connection diagram:

../_images/update.png

Pin num Pin description Notes
1 CPU_DEBUG_TX CPU Debug UART TX 3.3V Voltage level
2 CPU_DEBUG_RX CPU Debug UART RX 3.3V Voltage level
3 VCC3V3_DEBUG 3.3V power output only for debug
4 GND
5 NPU_DEBUG_TX NPU Debug UART TX 3.3V Voltage level
6 NPU_DEBUG_RX NPU Debug UART RX 3.3V Voltage level
7 CPU_UART4_RX CPU UART4 RX 1.8V Voltage level
8 CPU_UART4_TX CPU UART4 TX 1.8V Voltage level
14 GND
15 UPDATE_KEY Short with GND before DC plug in for loadermode
16 RESET_KEY Short with GND for system reset
17 GND

Windows Serial Port Tools

1、Connect the Debug port of the development board to the USB port of the PC, open the Device Manager to get the USB Serial Port number, as shown in the following figure:

../_images/SecureCRT_list.png

2、Install MobaXterm Serial Port Tool

3、Click session and select Serial。

4、Change Serial port to the COM port obtained from the Device Manager.

5、Change Speed (bsp) to 1500000。

6、 Click the OK button.

../_images/MobaXterm.png

Linux Serial Port Tools

1、Install minicom： sudo apt-get install minicom。

2、Connect the Debug port of the development board to the USB port of the host.

3、Open minicom with root privileges:： sudo minicom -s。

4、Open the Minicom menu：Enter CTRL-A + z。

5、Enter the Minicom configuration interface: Enter “O” to select “Configure Minicom”.

6、Enter serial port settings: Select “Serial port setup”.

7、Set the serial port device: Enter “A”, write “/dev/ttyUSB0”, and press Enter to confirm.

8、Disable flow control: Enter “F” and press Enter to confirm.

9、Set the baud rate: Enter “E”, then enter “A” until “Current 1500000 8N1” is displayed, then press Enter to confirm.

10、Save the settings: Select “Save setup as dfl”.

11、Exit the settings: Select “Exit”.

adb debugging

Introduction to Adb

Adb is short for Android Debug Bridge, which is Android’s command-line debugging tool. It can perform various functions, such as tracking system logs, uploading and downloading files, installing applications, etc.

Installing Adb on Windows

  1. Install USB Driver DriverAssitant_v5.11。

  2. Download adb.zip， extract adb.exe, AdbWinApi.dll, and AdbWinUsbApi.dll, and copy each one to the C:\Windows\System32 and C:\Windows\SysWOW64 directories.

Open a cmd window and run:

adb shell

If successful, you will enter the adb shell.

Installing Adb on Ubuntu

  1. Install the adb tool:

    sudo apt-get install android-tools-adb

  2. Add the device ID:

    mkdir -p ~/.android
vi ~/.android/adb_usb.ini
# add the following line:
0x2207

  3. Add udev rules for non-root users:

    sudo vi /etc/udev/rules.d/51-android.rules
# add the following line：
SUBSYSTEM=="usb", ATTR{idVendor}=="2207", MODE="0666"

  4. Reload udev rules:

    sudo udevadm control --reload-rules
sudo udevadm trigger

  5. Restart adb as a normal user:

    sudo adb kill-server
adb start-server

Then you can directly use adb, such as:

adb shell

Common Adb Commands

Connection Management

List all connected devices and their serial numbers:

adb devices

If there are multiple connected devices, you must distinguish them by serial number:

export ANDROID_SERIAL=<device serial number>
adb shell ls

You can also connect Adb over TCP/IP network:

adb tcpip 5555

Adb will restart on the device and listen on TCP port 5555, at which point you can unplug the USB cable.

If the device’s IP address is 192.168.1.100, execute the following command to connect:

adb connect 192.168.1.100:5555

Once connected, you can execute adb commands:

adb shell ps
adb logcat

Until you disconnect the adb connection:

adb disconnect 192.168.1.100:5555

Debugging

Query System Logs

Usage:

adb logcat [option] [Application label]

Example:

# View all logs
adb logcat

# View only part of the logs
adb logcat -s WifiStateMachine StateMachine

Collect Bug Reports

adb bugreport is used to collect error reports and some system information.

adb bugreport

# Save locally for easy editing and viewing
adb bugreport >bugreport.txt

Run shell

Open an interactive shell:

adb shell

Execute shell commands:

adb shell ps

Apk Management

Install Apk
adb install [option] example.apk

Options:
-l Forward lock
-r Reinstall the application while preserving the original data
-s Install to SD card instead of internal storage

Example:

# Install facebook.apk
adb install facebook.apk

# Upgrade twitter.apk
adb install -r twitter.apk

If the installation fails, check for common reasons:

  • INSTALL_FAILED_ALREADY_EXISTS: Try adding the -r parameter and reinstalling.

  • INSTALL_FAILED_SIGNATURE_ERROR: APK signatures are inconsistent, which may be due to differences between signatures and debug versions. If you confirm that the APK file signature is normal, you can use the adb uninstall command to uninstall the old application and then reinstall it.

  • INSTALL_FAILED_INSUFFICIENT_STORAGE: Not enough storage space.

Uninstall Apk
adb uninstall apk_name

Example:

adb uninstall com.android.chrome

The names of apk packages can be listed with the following command:

adb shell pm list packages -f
...
package:/system/app/Bluetooth.apk=com.android.bluetooth
...